My Fractal 75 is my go to whoop for all sorts of use.
It is a lot of fun.

It has handled some bad crashes, a duct broke due to cold weather so the front were changed from purple to black.
A camera broke in a little whoop event as the Caddx Ant (not lite) has bad cap placement on lower piece.
This has been since replaced with the Happymodel FXT FX17-B as it plugs right into the AIO.
I do prefer the Caddx Ant/ Ant Lite

I have flown it a lot and will continue to do so.
It is on the heavy side but I love it!

@kyleirelandtech

Fractal 75
Fractal Engineering - Fractal 75 – Frame Kit (F75 Lite)
BetaFPV Meteor75 Brushless Whoop Frame
Happymodel FXT FX17-B Camera
Happymodel X12 5in1 AIO (ELRS)
A30 Female w/ 20AWG Silicone Wire 80mm
RCInPower GTS V3 1003 18000KV Motor (x5)
Gemfan 1610 40mm Props (1.5mm) - Clear Blue
GNB 450mAh 1S 80C LiHV Battery (A30) (x6)

Throttle Limit = OFF to Scale
Throttle Mid = 0.5 to 1
Throttle Epo = 0 to 0.7

I love my Fractal 65 build.
The fact that if you break a duct it doesn't mean a whole frame replacement, Just get a new duct.
If you want a bigger battery holder just find or make one and 3D Print it out of TPU.
I snipped the three wires from the Caddx Ant Lite and three wires from the camera cable with AIO for soldering.

Just an amazing all around frame honestly, see the pictures of my build.
@kyleirelandtech

Fractal 65
Fractal Engineering - Fractal 65 - Frame Kit
Caddx Ant Lite FPV Camera (4:3)
Happymodel X12 5in1 AIO (ELRS)
A30 Female w/ 20AWG Silicone Wire 80mm
Fabric Tape Between FC and A30 Positive/Negative
RCInPower GTS V3 0802 22000KV Motor (x5
NewBeeDrone Azi Tri Blade Props 31mm (1.0mm Hub) - Clear
GNB 300mAh 1S 80C LiHV Battery (A30 Cabled) (x6)

Throttle Limit = OFF to Scale
Throttle Mid = 0.5 to 1
Throttle Epo = 0 to 0.7

Custom Battery Mounts;
https://www.printables.com/model/975859-fractal-65-modified-battery-holder-gnb-300mah-80-c

I love the Caddx Ant ant Caddx Ant Lite.
They can be pretty good in some low light conditions and look great during the day.
You might need to bump up goggle brightness or some bits to fly at night, or plug in the little Caddx board to adjust bits.

I do have one small negative, the Caddx Ant of mine did break but this is not the fault of Fractal.
Fractal recommends making a little tight 3D Print to go under the camera on the carbon plate. (not in the instructions)
This will stop you with the common issue where a cap on the lower camera can end up being popped off in a crash, especially when the camera hits the carbon in a crash.

@kyleirelandtech

I am 6 months into this Micro Drone hobby, so I am no expert, but I have been flying nearly every day. I have a Meteor 65, Meteor 75, Air 65, and Air 75. I wanted to try something different and I am VERY glad I did. Got a BNF F75, and I have to say it is the best Micro of them all. So much so, I ended up buying a Fractal 75 frame and transferring an Air75 to it. (If only I could get the FC flashed with QS....not sure why it wont).

Anyway, best money I have spent on a drone hands down. Amazing quality and you can tell there is a passion here.