Happymodel Superbee F4

$42.00

Features

  • The first AIO with onboard SPI ELRS receiver and 12A ESC
  • F4 FC, 12A, 1-2S ESC, 400mw VTX and ELRS Rx all-in-one package
  • Fractal Special: Unsoldered motor plugs for direct motor soldering
  • Excellent choice for a single board F65, F75 or Wingman

Description

Features

  • A simple and lightweight FC+ESC AIO without VTX for Digital video or external VTX
  • F411 FC, 5A, 1S ESC and Spi Frsky or ELRS Rx all-in-one package
  • Excellent choice for a HDZero F65 or F75

 

Specifications:

Flight controller

SuperbeeF4 Lite ELRS/FRSKY

SPI ELRS version Firmware target: CrazybeeF4SX1280 (BF) / crazybee_f4_elrs.brushless (QS)
SPI FRSKY version Firmware target: CrazybeeF4FR (BF) / crazybee_f4_frsky.brushless (QS)
MCU:STM32F411CEU6 (100MHz, 512K FLASH)
Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection)
Power supply: 1S Lipo Lihv battery input (DC 2.8V~4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in SPI Frsky/ExpressLRS receiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard 4in1 ESC MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV (2.8v~4.35v)
Currents: 5A continuous peak 6A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_8.HEX
Default protocol: DSHOT150/DSHOT300/DSHOT600
Onboard SPI ExpressLRS 2.4GHz Receiver Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna plug: IPEX
Telemetry output Power: <12dBm
Receiver protocol:  SPI ExpressLRS
Could bind with ELRS V2.0 firmware TX module
Onboard Frsky SPI D8 /D16 2.4GHz Receiver SPI BUS receiver Frsky D8/D16 compatible
Compatible Non EU transmitter D8 model and EU-LBT(Frsky_x_lbt)Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Based on CC2500 RF module Compatible with Futaba S-FHSS , Redpine protocol

Setup:

Note for Betaflight users: This flight controller being a spare part for F65/75 HDZero, the factory default device for OSD is “MSP
To use it with an analog camera you must edit this setting to enable OSD:
In Betaflight configurator, CLI tab, enter: “set osd_displayport_device = MAX7456” then “save”
You may then reconnect, go to OSD tab, upload a font and done.

Additional information

Weight 16.50 g
Dimensions 55 × 55 × 20 mm
HM SuperbeeF4 Receiver

ELRS, Frsky

Reviews

There are no reviews yet.

Be the first to review “Happymodel Superbee F4”

Your email address will not be published. Required fields are marked *

Post comment

You may also like…